63 lines
1.9 KiB
Markdown
63 lines
1.9 KiB
Markdown
|
# Serial ATA (SATA)
|
||
|
|
||
|
Helios64 uses the JMicron JMB585 Serial ATA (SATA) controller to provide 5x SATA 3.0 ports.
|
||
|
|
||
|
![SATA ports location](/helios64/img/sata/sata.jpg)
|
||
|
|
||
|
The SATA Controller is connected to RK3399 SoC via 2x lanes PCIe 2.0 offering 10GT/s (8Gbps) of bandwidth.
|
||
|
|
||
|
## SATA Controller Features
|
||
|
|
||
|
- 5 SATA ports,
|
||
|
- Command-based and FIS-based for Port Multiplier,
|
||
|
- Compliance with SATA Specification Revision 3.2,
|
||
|
- AHCI mode and IDE programming interface,
|
||
|
- Native Command Queue (NCQ),
|
||
|
- SATA link power saving mode (partial and slumber),
|
||
|
- SATA plug-in detection capable,
|
||
|
- Drive power control and staggered spin-up,
|
||
|
- SATA Partial / Slumber power management state.
|
||
|
|
||
|
## SATA Controller Diagram
|
||
|
|
||
|
![SATA Diagram](/helios64/img/sata/sata_diagram.jpg)
|
||
|
|
||
|
The above diagram shows the 2:1 MUX between SATA Port 1 and the M.2 connector. The M.2 SATA bus is shared with SATA Port 1, therefore if you install an M.2 SATA SSD card, SATA Port 1 (J3) will automatically get disabled.
|
||
|
|
||
|
## HDD Power
|
||
|
|
||
|
Helios64 provides on-board HDD power to supply up to 5x HDDs via header J7.
|
||
|
|
||
|
![J7 Location](/helios64/img/sata/j7.jpg)
|
||
|
|
||
|
The power delivery of the HDDs is devided into two group:
|
||
|
|
||
|
* HDD Rail A (Max. 3x Drives)
|
||
|
* HDD Rail B (Max. 2x Drives)
|
||
|
|
||
|
Helios64 implements a power staggering approach where *HDD Rail A* will be powered up first, then few seconds later *HDD Rail B* will be powered up. This power control scenario is performed to reduce the inrush current during disk spin-up.
|
||
|
|
||
|
### J7 Pinout
|
||
|
|
||
|
![J7 Location](/helios64/img/sata/j7_pinout.jpg)
|
||
|
|
||
|
| Pin | Signal Name |
|
||
|
|-----|-------------|
|
||
|
| 1 | 12V HDD Rail A |
|
||
|
| 2 | 12V HDD Rail B |
|
||
|
| 3 | 5V HDD Rail A |
|
||
|
| 4 | 5V HDD Rail B |
|
||
|
| 5 | GND |
|
||
|
| 6 | GND |
|
||
|
| 7 | GND |
|
||
|
| 8 | GND |
|
||
|
|
||
|
|
||
|
## HDD/SSD Harness
|
||
|
|
||
|
As part of Helios64 official enclosure, an HDD/SSD harness is provided to connected both SATA + Power signals between Helios64 board and the 5x HDD slots.
|
||
|
|
||
|
**Below the wiring diagram:**
|
||
|
|
||
|
![!HDD Harness](/helios64/img/sata/hdd_harness.png)
|