kobol-wiki/docs/helios64/install/first-start.md

##  **Step 1** - Connect to Helios64 serial console

### Under Windows

!!! Important
    For Windows version prior to Windows 10, you will need to install the FTDI driver in order to access the USB to serial bridge used by Helios64. You can find the driver [here](https://www.ftdichip.com/Drivers/VCP.htm).

1. [Download PuTTY](https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html) and install it on your computer.

2. Make sure your serial communication device is already detected by system.
![Serial detected](/helios64/install/img/serial-port.png)

2. Select connection type **serial**.<br>
![Putty connect](/helios64/install/img/putty-connect.png)

3. Setup serial port settings (Serial line : **COM3** and Speed : **1500000**), then press **'Open'**<br>
![Putty config](/helios64/install/img/putty-connect2.png)

!!! note
    The serial port detection may vary on different system, please make sure to check the device manager to get the information of correct serial port to connect to Helios64. Check this [link](https://tnp.uservoice.com/knowledgebase/articles/172101-determining-the-com-port-of-a-usb-to-serial-adapte) to learn how to determine the right COM port.


### Under Linux (via Terminal)

**1.** Install picocom

Use apt-get under Debian/Ubuntu

    $ sudo apt-get install picocom

Use yum under RHEL / CentOS / Fedora Linux

    $ sudo yum install picocom

**2.** Connect to serial with picocom

    $ sudo picocom -b 1500000 /dev/ttyUSB0

![Picocom](/helios64/install/img/picocom.png)

To exit picocom do **Ctrl-a** then **q** button in squence

!!! note
    Using command _ls -la /dev/ttyUSB*_ you should be able the find the USB to serial bridge device used by Helios64. Under Linux the device will be named **/dev/ttyUSBx**, where **x** is a digit.


### Under Mac OS (via Terminal)

!!! Important
    For Mac OS you might need to install the FTDI driver in order to access the USB to serial bridge used by Helios64. You can find the driver [here](https://www.ftdichip.com/Drivers/VCP.htm).

Connect serial using the *screen* command

    $ screen /dev/tty.usbserial-XXXXXXXX 1500000 -L

To exit the session do **Ctrl-a** then **Ctrl-k**

!!! note
    Using command _ls -la /dev/tty.usb*_ you should be able the find the USB to serial bridge device used by Helios64. Under Mac OS the device will be named **/dev/tty.usbserial-xxxxxxxx**, where **xxxxxxxx** is some serial number.

## **Step 2** - Power-Up Helios64

Now that everything is ready you can plug-in the AC adapter and push the [Power Button](/helios64/button/).

![Enclosure Power ON](/helios64/install/img/power-on_A.png)

If you are using Helios64 without an enclosure:

![Enclosure Power ON](/helios64/install/img/power-on_B.png)

You should see Helios64 boot logs on the Serial Console.

![Boot Output](/helios64/install/img/boot-output.png)

## **Step 3** - Log in

!!! note
    You might need to press **Enter** for the login prompt to come up.

**If system didn't auto logged-in. Default credential for Debian or Ubuntu image**

```bash
helios64 login: root
Password: 1234
```

You will be prompted to change the root password and then create a new user account.

![First Login](/helios64/install/img/first-login.png)

## **Step 4** - Check/Set IP address

### Check IP address

By default Helios64 will try to obtain an IP address via DHCP. To figure out what is the allocated IP address you will need to type the following command in the console.

```bash
ip addr show dev eth0
```

![Network Config](/helios64/install/img/ifconfig.png)

Here the IP address of Helios64 is **10.10.10.1**.

### Set IP address

If you wish to manually configure your IP address you can use the **armbian-config** tool.

```bash
armbian-config
```

Select the *Network* section:

![Armbian-config](/helios64/install/img/armbian-config.png)

Navigate to *IP* to configure your IPv4 address:

![Armbian-config](/helios64/install/img/armbian-config-network.png)

Select the Ethernet interface you want to assign a fixed IPv4 address. In this case we select **eth0** which correspond to LAN port 1:

![Armbian-config](/helios64/install/img/armbian-config-eth-select.png)

Select *Static*:

![Armbian-config](/helios64/install/img/armbian-config-ip-static.png)

Provide the IP Address, Netmask, and Gateway information that you want to assign:

![Armbian-config](/helios64/install/img/armbian-config-ip-set.png)

Press **ESC** till you exit armbian-config tool.

You will have to reboot for the network settings to take effect.
```bash
sudo reboot
```

!!! info
    You can also refer to the following Debian Wiki [Page](https://wiki.debian.org/NetworkConfiguration#Setting_up_an_Ethernet_Interface) for advanced network settings.

## **Step 5** - Connect to Helios64 via SSH

You can now connect by SSH to your Helios64 to carry on with your configuration.

Here is the example when we use linux client:

![SSH Login](/helios64/install/img/ssh_login.png)

You can use putty as the SSH client if you are using windows:

![Putty SSH](/helios64/install/img/putty_ssh.png)

## **What to do next ?**

You can use **armbian-config** which provides an easy way to install 3rd party applications like *OpenMediaVault*, *NextCloud*, *Syncthing*, *Emby* and many more.

Here an example on how to install software OpenMediaVault (OMV) using the armbian-config.

```bash
sudo armbian-config
```

Select *Software* section:

![!armbian-config Main Menu](/helios64/img/omv/install-1.png)

Navigate to *Softy*:

![!armbian-config Software](/helios64/img/omv/install-2.png)

Then choose *OMV*, to install the OpenMediaVault:

![!armbian-config Selection](/helios64/img/omv/install-3.png)

Wait the install process to complete:

![!armbian-config Selection](/helios64/img/omv/install-4.png)

**Now you should be able to connect to OpenMediaVault (OMV) Control Panel.**

Open your web browser and go to the one of the following addresses :

- http://helios64.local
- http://xxx.xxx.xxx.xxx ([How to check Helios64 IP address](#step-7-checkset-ip-address))

Default credential :

- Username: admin
- Password: openmediavault