Update Assembly, Install and M.2 pages.

*resize all assembly pic to 1080p

docs/helios64/install.md

@@ -74,25 +74,26 @@ sudo dd if=Armbian_20.08.0_Helios64_buster_current_5.7.15.img of=/dev/sdX bs=4M
 !!! note
     /dev/sdX is where the microSD is mapped in your Linux machine, change the 'X' to your corresponding mapped device. If you set /dev/sdX to a wrong device then you might risk erasing a hard drive or different device than the designated microSD.
 
-##  **Step 3** - Power-up Helios64
+##  **Step 3** - Wire Helios64
-
-**Before powering-up make sure:**
-
-1. You inserted the prepared microSD Card.
-
-2. You connected your computer to the serial port with the Type-C to Type-A USB cable.
-
-3. You connected Helios64 to your home network with the Ethernet cable.
-
-4. You plugged-in properly the DC power connector before powering-up the AC adapter.
-
-![Connections](/helios64/img/install/connections.jpg)
-
-**Now you can plug-in the AC adapter and push the [Power Button](/helios64/button/)**
 
 !!! warning
     Always proceed with caution when manipulating 110/220V appliance.
 
+1. Insert the prepared microSD Card.
+
+2. Connect your computer to the serial port with the Type-C to Type-A USB cable.
+
+3. Connect Helios64 to your home network with the Ethernet cable.<br>*Choose LAN2 port if you have 2.5Gb network.*
+
+4. Plug-in the DC power connector. **Don't power-up the Power Adapter yet.**
+
+![Connections with Enclosure](/helios64/img/install/connections_A.png)
+
+If you are using Helios64 without an enclosure:
+
+![Connections without Enclosure](/helios64/img/install/connections_B.png)
+
+
 ##  **Step 4** - Connect to Helios64 serial console
 
 !!! Important
@@ -150,12 +151,27 @@ To exit the session do **Ctrl-a** then **Ctrl-k**
 !!! note
     Using command _ls -la /dev/tty.usb*_ you should be able the find the USB to serial bridge device used by Helios64. Under Mac OS the device will be named **/dev/tty.usbserial-xxxxxxxx**, where **xxxxxxxx** is some serial number.
 
-## **Step 5** - Log in
+
+## **Step 5** - Power-Up Helios64
+
+Now that everything is ready you can plug-in the AC adapter and push the [Power Button](/helios64/button/).
+
+![Enclosure Power ON](/helios64/img/install/power-on_A.png)
+
+If you are using Helios64 without an enclosure:
+
+![Enclosure Power ON](/helios64/img/install/power-on_B.png)
+
+You should see Helios64 boot logs on the Serial Console.
+
+![Boot Output](/helios64/img/install/boot-output.png)
+
+## **Step 6** - Log in
 
 !!! note
     You might need to press **Enter** for the login prompt to come up.
 
-**Default credential for Debian or Ubuntu image**
+**If system didn't auto logged-in. Default credential for Debian or Ubuntu image**
 
 ```bash
 helios64 login: root
@@ -164,9 +180,9 @@ Password: 1234
 
 You will be prompted to change the root password and then create a new user account.
 
-![First Login](/helios64/img/install/first-boot-userpass.png)
+![First Login](/helios64/img/install/first-login.png)
 
-## **Step 6** - Check/Set IP address
+## **Step 7** - Check/Set IP address
 
 ### Check IP address
 
@@ -178,7 +194,7 @@ ip addr show dev eth0
 
 ![Network Config](/helios64/img/install/ifconfig.png)
 
-Here the IP address of Helios64 is **10.10.10.73**.
+Here the IP address of Helios64 is **10.10.10.1**.
 
 ### Set IP address
 
@@ -192,14 +208,14 @@ Select the *Network* section:
 
 ![Armbian-config](/helios64/img/install/armbian-config.png)
 
-Select the ethernet you want to assign IP Address to, in this case we select eth0 for the first Ethernet:
-
-![Armbian-config](/helios64/img/install/armbian-config-eth-select.png)
-
 Navigate to *IP* to configure your IPv4 address:
 
 ![Armbian-config](/helios64/img/install/armbian-config-network.png)
 
+Select the Ethernet interface you want to assign a fixed IPv4 address. In this case we select **eth0** which correspond to LAN port 1:
+
+![Armbian-config](/helios64/img/install/armbian-config-eth-select.png)
+
 Select *Static*:
 
 ![Armbian-config](/helios64/img/install/armbian-config-ip-static.png)
@@ -218,7 +234,7 @@ sudo reboot
 !!! info
     You can also refer to the following Debian Wiki [Page](https://wiki.debian.org/NetworkConfiguration#Setting_up_an_Ethernet_Interface) for advanced network settings.
 
-## **Step 7** - Connect to Helios64 via SSH
+## **Step 8** - Connect to Helios64 via SSH
 
 You can now connect by SSH to your Helios64 to carry on with your configuration.
 

docs/helios64/kit.md

@@ -82,6 +82,9 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 
 ### STEP 3 - Install Helios64 Board
 
+!!! note
+    If you want to install an M.2 SSD, it is recommended to do it now. Please refer to the following [page](/helios64/m2/#installation).
+
 > **Position the Helios64 board on top of the 4x standoffs.**
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic7.png)
@@ -102,7 +105,7 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 
 > **Connect the 6-Pin Molex connector to Helios64 board.**
 
-![Battery Ports](/helios64/img/kit/port-battery.png)
+![Battery Ports](/helios64/img/kit/connector-battery.png)
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic11.png)
 
@@ -113,7 +116,7 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 
 > **Connect the Front Panel USB and IDC connectors to Helios64 board.**
 
-![!Front Panel Ports](/helios64/img/kit/port-front-panel.png)
+![!Front Panel Ports](/helios64/img/kit/connector-front-panel.png)
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic12.png)
 
@@ -130,18 +133,18 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 
 > **Connect the 8-Pin Molex connector to Helios64 board.**
 
-![!HDD Power Port](/helios64/img/kit/port-hdd-power.png)
+![!HDD Power Connector](/helios64/img/kit/connector-hdd-power.png)
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic15.png)
 
 > **Install HDD Slot 1 connector with 2x screws (M3 x 5mm).**
 
 !!! important
-    Pay attention to HDD Slot connector orientation. The 4 power wires are supposed to be on the left, while the SATA cable is on the right. Power wires and SATA cable will cross each others which is expected. If you install the HDD Slot connector wrongly, then you won't be able to insert an HDD and might damage the connector.
+    Pay attention to HDD Slot connector orientation. The 4 power wires are supposed to be on the left, while the SATA cable is on the right. Power wires and SATA cable will cross each others which is expected. If you install the HDD Slot connector wrongly, then you won't be able to insert the HDD and might damage the connector.
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic16.png)
 
-> **Connect SATA connector to Helios64 SATA port 1. Then Secure the SATA cable with a cable tie like on the drawing below (cut the cable zip tie excess).**
+> **Connect SATA cable to Helios64 board SATA Port 1. Then Secure the SATA cable with a cable tie like on the drawing below (cut the cable zip tie excess).**
 
 ![!Kit Assembly](/helios64/img/kit/connector-sata.png)
 
@@ -151,14 +154,14 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic18.png)
 
-> **Repeat the same actions for HDD Slot 2 connector and connect its SATA connector to Helios64 SATA port 2.**
+> **Repeat the same actions for HDD Slot 2 connector and connect its SATA cable to Helios64 board SATA Port 2.**
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic19.png)
 
 > **Repeat the same actions for HDD Slot 3, 4 and 5 connectors. The completed harness installation should look like the drawing below.**
 
 !!! important
-    The harness includes 4x capacitors (little black cylinders) which their own attached wires. While install HDD Slot 3 and 4 connector, you need to secure those capacitors together with the HDD power wires as shown in the drawing below.
+    The harness includes 4x capacitors (little black cylinders) which their own attached wires. While install HDD Slot 3 and 4 connectors, you need to secure these capacitors together with the HDD power wires as shown in the drawing below.
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic20.png)
 
@@ -178,42 +181,49 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 > **Install the Back Panel Sticker.**
 
 !!! important
-    Position the sticker to be perfectly aligned with the port connector holes.
+    Position the sticker to be perfectly aligned with the port holes.
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic25.png)
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic26.png)
 
-> **Connect Fans to Helios64 board.**
+> **Connect Fan cables to Helios64 board Fan connectors.**
 
-![!Fan Ports](/helios64/img/kit/port-fans.png)
+![!Fan Ports](/helios64/img/kit/connector-fans.png)
 
-![!Kit Assembly](/helios64/img/kit/assembly_pic28.png)
+![!Kit Assembly](/helios64/img/kit/assembly_pic27.png)
 
 > **Use cable ties like on the drawing below (cut the cable zip tie excess).**
 
-![!Kit Assembly](/helios64/img/kit/assembly_pic29.png)
+![!Kit Assembly](/helios64/img/kit/assembly_pic28.png)
 
 ### STEP 8 - Reassemble Enclosure
 
 > **Insert Backplane inside Aluminum enclosure.**
 
+![!Kit Assembly](/helios64/img/kit/assembly_pic29.png)
+
+> **Secure Backplane to the enclosure with 8x screws (M3x5mm Hexagon Head).**
+
 ![!Kit Assembly](/helios64/img/kit/assembly_pic30.png)
 
-> **Secure Backplane to enclosure with 8x screws (M3x5mm Hexagon Head).**
-
-![!Kit Assembly](/helios64/img/kit/assembly_pic31.png)
-
 > **Insert Back Panel**
 
 !!! important
     Insure you are well aligned with Helios64 Board ports when inserting the Back Panel.
 
-![!Kit Assembly](/helios64/img/kit/assembly_pic32.png)
+![!Kit Assembly](/helios64/img/kit/assembly_pic31.png)
 
 > **Secure Back Panel with 4x screws (M3x5mm Counter Sink Head).**
 
-![!Kit Assembly](/helios64/img/kit/assembly_pic33.png)
+![!Kit Assembly](/helios64/img/kit/assembly_pic32.png)
+
+> **Install 4x Foam Pads on the bottom side of the enclosure**
+
+![!Kit Assembly](/helios64/img/kit/assembly_pic33_A.png)
+
+![!Kit Assembly](/helios64/img/kit/assembly_pic33_B.png)
+
 
 ### STEP 9 - Prepare HDD Trays
 
@@ -224,6 +234,8 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic34.png)
 
+![!Kit Assembly](/helios64/img/kit/assembly_pic34.png)
+
 ![!Kit Assembly](/helios64/img/kit/assembly_pic35.png)
 
 ### STEP 10 - Use 2.5" Adapter **(Optional)**
@@ -245,10 +257,11 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 > **Slot in the HDD Trays.**
 
 !!! important
-    Pay attention to the orientation, you don't want to damage the SATA connector when inserting the Trays.
+    * Pay attention to the orientation, you don't want to damage the SATA connectors when inserting the Trays.
+    * The plastic Trays might feel difficult to insert at first. They will loosen up a bit with time.
 
 !!! note
-    Slot numbering starts from left with Slot 1 (SATA port 1).
+    Slot numbering starts from left with Slot 1 (SATA Port 1). You can use provided Number stickers to identify each HDD Trays.
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic36.png)
 
@@ -259,7 +272,7 @@ The Enclosure Kit has been specially designed for the Helios64 board. The follow
 > **Install the Front Panel.**
 
 !!! note
-    The Front Panel should hold by itself thanks to the 4x round magnets.
+    The Front Panel should hold by itself thanks to the 4x pre-installed round magnets.
 
 ![!Kit Assembly](/helios64/img/kit/assembly_pic43.png)
 

docs/helios64/m2.md

@@ -20,6 +20,29 @@ The board provides mounting holes for 2260 and 2280 cards.
 
 ![M.2 Form Factor](/helios64/img/m2/m2_form_factor.jpg)
 
+## Installation
+
+In order to install a M.2 device you will have to first mount a metal standoff on Helios64 board. Choose the mounting hole according to your M.2 device size (either 2260 or 2280).
+
+> **Install the standoff in one of the mounting hole with one M3x3mm screw.**
+
+![M.2 SSD Install 1](/helios64/img/m2/m2_ssd_install_pic1.png)
+
+![M.2 SSD Install 2](/helios64/img/m2/m2_ssd_install_pic2.png)
+
+!!! Note
+		Standoff and screws are provided with Helios64 board.
+
+> **Insert the device in M.2 the slot.**
+
+![M.2 SSD Install 3](/helios64/img/m2/m2_ssd_install_pic3.png)
+
+> **Secure the M.2 device with the other M3x3mm screw.**
+
+![M.2 SSD Install 4](/helios64/img/m2/m2_ssd_install_pic4.png)
+
+![M.2 SSD Install 5](/helios64/img/m2/m2_ssd_install_pic5.png)
+
 ## Usage
 
 The M.2 interface on Helios64 only supports SATA 3.0 and USB 2.0 buses.