The **mdadm** utility can be used to create and manage storage arrays using Linux's software RAID capabilities. In this guide, we will show how to create different RAID configurations : * RAID1 (for 2x HDD) * RAID6 (for 4x HDD) * RAID10 (for 4x HDD) ## Install mdadm sudo apt-get install mdadm ### Fix mdadm You might see the following error message in your boot messages *"mdadm: initramfs boot message: /scripts/local-bottom/mdadm: rm: not found"*. This minor issue has been fixed in all our latest Armbian images for Helios4. To fix this minor issue simply edit the *mdadm* hook script of initramfs: sudo nano /usr/share/initramfs-tools/hooks/mdadm Add **copy_exec /bin/rm /bin** after the following lines: copy_exec /sbin/mdadm /sbin copy_exec /sbin/mdmon /sbin Then update initramfs: sudo update-initramfs -u ## Identify you Storage Drives To get started, you will need first to identify the storage drives that you will use to compose your RAID array: lsblk -o NAME,SIZE,FSTYPE,TYPE,MOUNTPOINT Output NAME SIZE FSTYPE TYPE MOUNTPOINT sda 1.8T disk sdb 1.8T disk sdc 1.8T disk sdd 1.8T disk mmcblk0 14.9G disk └─mmcblk0p1 14.7G ext4 part / zram0 50M disk /var/log zram1 504.4M disk [SWAP] zram2 504.4M disk [SWAP] As you can see above, we have four drives without a filesystem, each of 1.8TB in size. So our drives are /dev/sda, /dev/sdb, /dev/sdc and /dev/sdd. !!! note To avoid any confusion at identifying the right drive, start Helios4 without any type of USB storage connected to it. ## Create Array ### Create RAID 1 Array To create a RAID 1 array with 2x drives, pass them to the mdadm --create command. You will have to specify the device name you wish to create (**/dev/md0** in our case), the RAID level, and the number of devices: sudo mdadm --create --verbose /dev/md0 --level=1 --raid-devices=2 /dev/sda /dev/sdb If the drives you are using are not partitioned with the boot flag enabled, you will likely be given the following warning. It is safe to type **y** to continue: mdadm: Note: this array has metadata at the start and may not be suitable as a boot device. If you plan to store '/boot' on this device please ensure that your boot-loader understands md/v1.x metadata, or use --metadata=0.90 mdadm: size set to 1953383488K mdadm: automatically enabling write-intent bitmap on large array Continue creating array? y mdadm: Defaulting to version 1.2 metadata mdadm: array /dev/md0 started. The mdadm tool will start to mirror the drives. This can take some time to complete, but the array can be used during this time. You can monitor the progress of the mirroring by checking the /proc/mdstat file: cat /proc/mdstat Output Personalities : [raid1] md0 : active raid1 sdb[1] sda[0] 1953383488 blocks super 1.2 [2/2] [UU] [>....................] resync = 0.9% (19054272/1953383488) finish=213.6min speed=150885K/sec bitmap: 15/15 pages [60KB], 65536KB chunk unused devices: As you can see in the second line, the /dev/md0 device has been created with the RAID 1 configuration using the /dev/sda and /dev/sdb devices. The fourth line shows the progress of the syncing. You can continue the guide while this process completes. !!! note If your system is configured to [display RAID fault on the LED2](#configure-fault-led), then you should also see the red LED2 blinking while your array is (re-)syncing. ### Create RAID 6 Array To create a RAID 6 array with 4x drives, pass them to the mdadm --create command. You will have to specify the device name you wish to create (**/dev/md0** in our case), the RAID level, and the number of devices: sudo mdadm --create --verbose /dev/md0 --level=6 --raid-devices=4 /dev/sda /dev/sdb /dev/sdc /dev/sdd The mdadm tool will start to configure the array (it actually uses the recovery process to build the array for performance reasons). This can take some time to complete, but the array can be used during this time. You can monitor the progress of the mirroring by checking the /proc/mdstat file: cat /proc/mdstat Output Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sdd[3] sdc[2] sdb[1] sda[0] 3906766848 blocks super 1.2 level 6, 512k chunk, algorithm 2 [4/4] [UUUU] [>....................] resync = 0.3% (7171152/1953383424) finish=471.0min speed=68866K/sec bitmap: 15/15 pages [60KB], 65536KB chunk unused devices: As you can see in the second line, the /dev/md0 device has been created with the RAID 6 configuration using the /dev/sda, /dev/sdb, /dev/sdc and /dev/sdd devices. The fourth line shows the progress of the syncing. You can continue the guide while this process completes. !!! note If your system is configured to [display RAID fault on the LED2](#configure-fault-led), then you should also see the red LED2 blinking while your array is (re-)syncing. ### Create RAID 10 Array To create a RAID 10 array with 4x drives, pass them to the mdadm --create command. You will have to specify the device name you wish to create (**/dev/md0** in our case), the RAID level, and the number of devices: sudo mdadm --create --verbose /dev/md0 --level=10 --raid-devices=4 /dev/sda /dev/sdb /dev/sdc /dev/sdd The mdadm tool will start to configure the array (it actually uses the recovery process to build the array for performance reasons). This can take some time to complete, but the array can be used during this time. You can monitor the progress of the mirroring by checking the /proc/mdstat file: cat /proc/mdstat Output Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [raid10] md0 : active raid10 sdd[3] sdc[2] sdb[1] sda[0] 3906766848 blocks super 1.2 512K chunks 2 near-copies [4/4] [UUUU] [>....................] resync = 0.5% (20708608/3906766848) finish=305.0min speed=212294K/sec bitmap: 30/30 pages [120KB], 65536KB chunk unused devices: As you can see in the second line, the /dev/md0 device has been created with the RAID 10 configuration using the /dev/sda, /dev/sdb, /dev/sdc and /dev/sdd devices. The fourth line shows the progress of the syncing. You can continue the guide while this process completes. !!! note If your system is configured to [display RAID fault on the LED2](#configure-fault-led), then you should also see the red LED2 blinking while your array is (re-)syncing. ## Create and Mount the Filesystem !!! note The Helios4 System-On-Chip is a 32bit architecture, therefore the max partition size supported is 16TB. If your RAID array is more than 16TB of usable space, then you will need to create more than just one partition. You can use **fdisk /dev/md0** command to create several partitions on your array, then instead of using */dev/md0* for the below commands, it will be */dev/md0p1*, */dev/md0p2*, etc... Create a filesystem on the array: sudo mkfs.ext4 -F /dev/md0 Create a mount point to attach the new filesystem: sudo mkdir -p /mnt/md0 You can mount the filesystem by typing: sudo mount /dev/md0 /mnt/md0 Check whether the new space is available by typing: df -h -x devtmpfs -x tmpfs Output Filesystem Size Used Avail Use% Mounted on /dev/mmcblk0p1 15G 842M 14G 6% / /dev/zram0 49M 784K 45M 2% /var/log /dev/md0 1.8T 77M 1.7T 1% /mnt/md0 The new filesystem is mounted and accessible. ## Save the Array Layout To make sure that the array is reassembled automatically at boot, we will have to modify /etc/mdadm/mdadm.conf file. You can automatically scan the active array and append the file by typing: sudo mdadm --detail --scan | sudo tee -a /etc/mdadm/mdadm.conf Afterwards, you can update the initramfs, so that the array will be available during the early boot stage: sudo update-initramfs -u Add the new filesystem mount options to the /etc/fstab file for automatic mounting at boot: echo '/dev/md0 /mnt/md0 ext4 defaults,nofail,discard 0 0' | sudo tee -a /etc/fstab **Your RAID array should now automatically be assembled and mounted at each boot!** ## Check your RAID Array State To get a detailed picture of your array setup and its state you can use the following command: sudo mdadm -D /dev/md0 This is the output when the array is in good health, you can see the line showing **State : clean**. /dev/md0: Version : 1.2 Creation Time : Sun Jul 29 14:59:58 2018 Raid Level : raid10 Array Size : 3906766848 (3725.78 GiB 4000.53 GB) Used Dev Size : 1953383424 (1862.89 GiB 2000.26 GB) Raid Devices : 4 Total Devices : 4 Persistence : Superblock is persistent Intent Bitmap : Internal Update Time : Tue Nov 13 06:21:03 2018 State : clean Active Devices : 4 Working Devices : 4 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 512K Name : helios4:0 (local to host helios4) UUID : ea143418:153e050e:ac86d56c:07547815 Events : 95892 Number Major Minor RaidDevice State 0 8 0 0 active sync set-A /dev/sda 1 8 16 1 active sync set-B /dev/sdb 2 8 32 2 active sync set-A /dev/sdc 3 8 48 3 active sync set-B /dev/sdd In below example the array has a failed drive, you can see the line **State : clean, degraded** and that the RaidDevice 2 (/dev/sdc) is removed. The array is still active but in a degraded state because it requires /dev/sdc to be replaced as soon as possible. /dev/md0: Version : 1.2 Creation Time : Sun Jul 29 14:59:58 2018 Raid Level : raid10 Array Size : 3906766848 (3725.78 GiB 4000.53 GB) Used Dev Size : 1953383424 (1862.89 GiB 2000.26 GB) Raid Devices : 4 Total Devices : 3 Persistence : Superblock is persistent Intent Bitmap : Internal Update Time : Tue Nov 13 08:34:06 2018 State : clean, degraded Active Devices : 3 Working Devices : 3 Failed Devices : 0 Spare Devices : 0 Layout : near=2 Chunk Size : 512K Name : helios4:0 (local to host helios4) UUID : ea143418:153e050e:ac86d56c:07547815 Events : 95892 Number Major Minor RaidDevice State 0 8 0 0 active sync set-A /dev/sda 1 8 16 1 active sync set-B /dev/sdb - 0 0 2 removed /dev/sdc 3 8 48 3 active sync set-B /dev/sdd 2 8 32 - faulty /dev/sdc ## Replace a Failed Drive Once you have identified the failed drive with the command **mdadm -D**, as shown in the previous section, you will need to do the following steps to replace the failed drive: 1. Mark the faulty drive as failed. `mdadm /dev/md0 --fail /dev/sdc` 2. Remove the drive from the array. `mdadm /dev/md0 --remove /dev/sdc` 3. Identify which physical drive is to be replaced. `readlink -f on /sys/block/* | grep sdc` `/sys/devices/platform/soc/soc:internal-regs/f10e0000.sata/ata3/host2/target2:0:0/2:0:0:0/block/sdc` In this example the faulty drive is the one connected to the SATA port 3 (**ata3**) of the board. 4. Shutdown your system and replace the faulty drive. `sudo halt` 5. Power-up your Helios4. 6. Add the new drive to the array. You will need to use **lsblk** command to figure out what's the device name of the new drive. Most probably it will be the same than before. `sudo mdadm /dev/md0 --add /dev/sdc` Finally check the array is correctly re-building the new drive. `sudo mdadm -d /dev/md0` Number Major Minor RaidDevice State 0 8 0 0 active sync set-A /dev/sda 1 8 16 1 active sync set-B /dev/sdb 4 0 0 2 spare rebuilding /dev/sdc 3 8 48 3 active sync set-B /dev/sdd We can see that /dev/sdc is being rebuilt. `cat /proc/mdstat` Personalities : [raid1] [raid0] [raid6] [raid5] [raid4] [raid10] md0 : active raid10 sdd[3] sdc[4] sdb[1] sda[0] 3906766848 blocks super 1.2 512K chunks 2 near-copies [4/4] [UU_U] [>....................] recovery = 0.5% (20708608/3906766848) finish=305.0min speed=212294K/sec You can see the rebuild progress. ## Setup Error Notification (Recommended) In order to get notified or to see visual indication that something is wrong with your array you can configure *email alerts* and/or *error LED*. ### Configure Email Alerts Receive a notification whenever mdadm detects something wrong with your array. This is very important since you don't want to miss out an issue on your array in order to have time to take the right actions. sudo nano /etc/mdadm/mdadm.conf Edit the following section and replace root by your email address. # instruct the monitoring daemon where to send mail alerts MAILADDR root !!! important You will need to install and configure **postfix** or **sendmail**. ### Configure Fault LED Make the Red Fault LED (LED2) indicates if an error has been detected on your array. The below script will light up the LED2 if an error occurs on an array, and make LED2 blink during reconstruction of a degraded array. !!! note Latest Armbian builds, starting version 5.68, are already configured to display RAID faults on Red Fault LED (LED2), therefore you could skip this section. However in some use case file */etc/mdadm/mdadm.conf* might have been overwritten by applications such as OpenMediaVault, so it is advised to double check it is properly configured. First create the script *mdadm-fault-led.sh* sudo nano /usr/sbin/mdadm-fault-led.sh Copy the following script. ```bash #!/bin/bash # # Make Red Fault LED (LED2) reports mdadm error events. # EVENT=$1 # RED Fault LED trigger # trigger none = LED not-blinking if LED on # trigger timer = LED blinking if LED on TRIGGER=/sys/class/leds/helios4\:red\:fault/trigger # RED Fault LED brightness # britghness 0 = LED off # britghness 1 = LED on BRIGHTNESS=/sys/class/leds/helios4\:red\:fault/brightness # Active component device of an array has been marked as faulty OR A newly noticed array appears to be degraded. if [[ $EVENT == "Fail" || $EVENT == "DegradedArray" ]]; then echo none > $TRIGGER echo 1 > $BRIGHTNESS fi # An md array started reconstruction if [ $EVENT == "RebuildStarted" ]; then echo timer > $TRIGGER echo 1 > $BRIGHTNESS fi # An md array that was rebuilding, isn't any more, either because it finished normally or was aborted. if [ $EVENT == "RebuildFinished" ]; then echo none > $TRIGGER echo 0 > $BRIGHTNESS fi # Test RED Fault LED if [ $EVENT == "TestMessage" ]; then echo timer > $TRIGGER echo 1 > $BRIGHTNESS sleep 5 echo 0 > $BRIGHTNESS fi ``` Make the script executable. sudo chmod a+x /usr/sbin/mdadm-fault-led.sh Edit mdadm configuration sudo nano /etc/mdadm/mdadm.conf and add the following section. # trigger program when an event detected PROGRAM /usr/sbin/mdadm-fault-led.sh Restart mdmonitor service. sudo systemctl restart mdmonitor.service ### Test alerts You can test your error notification setup by doing the following: `sudo mdadm --monitor --scan --test -1` ## Import an Existing RAID Array If for some reasons you want to add an existing array to your system (e.g you just did a new fresh install of your operating system), you can use the following command to detect your existing array. Find the array with the following command: sudo mdadm --detail --scan Output ARRAY /dev/md/helios4:0 metadata=1.2 name=helios4:0 UUID=803a730b:7e13a859:08b9725e:c2eff9d5 We can see that an existing array has been detected as */dev/md/helios4:0* . You might want to check directly /proc/mdstat to find the device number. This will be easier to use when configuring your mounting points. cat /proc/mdstat Ouput Personalities : [raid10] [raid0] [raid1] [raid6] [raid5] [raid4] md127 : active (auto-read-only) raid10 sdd[3] sda[0] sdc[2] sdb[1] 234323968 blocks super 1.2 512K chunks 2 near-copies [4/4] [UUUU] bitmap: 0/2 pages [0KB], 65536KB chunk unused devices: As we can see here the array is identified as device **md127** (/dev/md127). Then refer to previous [section](#save-the-array-layout) to save the array layout in mdadm configuration and mount the file system but take in consideration that now device name is **/dev/md127** not anymore /dev/md0. ## Reset Existing RAID Devices !!! warning This process will completely destroy the array and any data written to it. Make sure that you are operating on the correct array and that you have copied off any data you need to retain prior to destroying the array. Find the active arrays in the /proc/mdstat file by typing: cat /proc/mdstat Output Personalities : [raid0] [linear] [multipath] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid6 sdd[3] sdc[2] sdb[1] sda[0] 3906766848 blocks super 1.2 level 6, 512k chunk unused devices: Unmount the array from the filesystem: sudo umount /dev/md0 Then, stop and remove the array by typing: sudo mdadm --stop /dev/md0 sudo mdadm --remove /dev/md0 Find the devices that were used to build the array with the following command: lsblk -o NAME,SIZE,FSTYPE,TYPE,MOUNTPOINT Output NAME SIZE FSTYPE TYPE MOUNTPOINT sda 1.8T linux_raid_member disk └─md0 3.7T ext4 raid6 sdb 1.8T linux_raid_member disk └─md0 3.7T ext4 raid6 sdc 1.8T linux_raid_member disk └─md0 3.7T ext4 raid6 sdd 1.8T linux_raid_member disk └─md0 3.7T ext4 raid6 mmcblk0 14.9G disk └─mmcblk0p1 14.7G ext4 part / zram0 50M disk /var/log zram1 504.4M disk [SWAP] zram2 504.4M disk [SWAP] !!! important Keep in mind that the /dev/sd* names can change any time you reboot! Check them every time to make sure you are operating on the correct devices. After discovering the devices used to create an array, zero their superblock to reset them to normal: sudo mdadm --zero-superblock /dev/sda sudo mdadm --zero-superblock /dev/sdb sudo mdadm --zero-superblock /dev/sdc sudo mdadm --zero-superblock /dev/sdd You should remove any of the persistent references to the array. Edit the /etc/fstab file and comment out or remove the reference to your array: ```bash sudo nano /etc/fstab # /dev/md0 /mnt/md0 ext4 defaults,nofail,discard 0 0 ``` Also, comment out or remove the array definition from the /etc/mdadm/mdadm.conf file: ```bash sudo nano /etc/mdadm/mdadm.conf # ARRAY /dev/md0 metadata=1.2 name=mdadmwrite:0 UUID=7261fb9c:976d0d97:30bc63ce:85e76e91 ``` Finally, update the initramfs again: sudo update-initramfs -u At this point, you should be ready to reuse the storage devices individually, or as devices of a different array. *Tuto Source: [link](https://www.digitalocean.com/community/tutorials/how-to-create-raid-arrays-with-mdadm-on-ubuntu-16-04)*