kobol-wiki/docs/helios64/led.md

On-Board LEDs

Pinout Table

Pin	LED number	Remarks
1	-	3.3V supply
2	-	Not connected
3	LED1	Active-low
4	LED2	Active-low
5	LED3	Active-low
6	LED4	Active-low
7	LED5	Active-low
8	LED6	Active-low
9	LED7	Active-low
10	-	GND

!!! info LED1 - LED7 is preconfigured for certain indicator under Linux, see LED under Linux section.

Wiring Diagram

Since the signals to control the LEDs are active low, connect the pin to LED's cathode. Below a wiring diagram example.

LED under Linux

LED	Name	Default Trigger	Remarks
LED1	helios4:green:status	heartbeat	Blinking periodically
LED2	helios4:red:fault	none	See Configuring Fault LED
LED3	helios4:green:ata1	ata1	Blinking on SATA1 activity
LED4	helios4:green:ata2	ata2	Blinking on SATA2 activity
LED5	helios4:green:ata3	ata3	Blinking on SATA3 activity
LED6	helios4:green:ata4	ata4	Blinking on SATA4 activity
LED7	helios4:green:usb	usb-host	Blinking on USB activity, any port

!!! note ata trigger requires additional patch to mainline kernel. The patch can be found here. Armbian builds are already patched, so no action is required.

The LEDs can be accessed under LEDs class in sysfs.

root@helios4:~/# ls -l /sys/class/leds/

lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:green:ata1 -> ../../devices/platform/io-leds/leds/helios4:green:ata1
lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:green:ata2 -> ../../devices/platform/io-leds/leds/helios4:green:ata2
lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:green:ata3 -> ../../devices/platform/io-leds/leds/helios4:green:ata3
lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:green:ata4 -> ../../devices/platform/io-leds/leds/helios4:green:ata4
lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:green:status -> ../../devices/platform/system-leds/leds/helios4:green:status
lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:green:usb -> ../../devices/platform/io-leds/leds/helios4:green:usb
lrwxrwxrwx 1 root root 0 Dec  4 06:57 helios4:red:fault -> ../../devices/platform/system-leds/leds/helios4:red:fault

LEDs Trigger

• none

No automatic trigger. Manually control the LED by manipulating "brightness". More info see Configuring LED trigger.

• heartbeat

LED "double" flashes at a load average based rate. The interval might change during heavy load. If the LED no longer blinks, it means the system is locked-up or hung and has to be reset.

• ataN

LED blinks on any read/write activity at specific SATA port.

• usb-host

LED blinks on USB activity at any port.

• panic

This trigger allows LEDs to be configured to blink on a kernel panic.

• timer

This allows LEDs to be controlled by a programmable timer via sysfs. delay_on to set how long the LED turned on and delay_off to set how long the LED turned off.

Configuring LED trigger

To configure, simply set the trigger type. For example to set Status LED triggered by timer

echo timer | sudo tee -a  /sys/class/leds/helios4\:green\:status/trigger

Some of the triggers may expose additional parameters that can be configured further.

On none trigger, to turn ON the LED set the brightness bigger than 0.

echo 1 | sudo tee -a  /sys/class/leds/helios4\:green\:status/brightness

and to turn OFF the LED set the brightness to 0.

echo 0 | sudo tee -a  /sys/class/leds/helios4\:green\:status/brightness

On timer trigger, it will exposed delay_on and delay_off with default value of 0.5 seconds for both. To change the delay, set the respective parameter (value in milliseconds)

echo 1000 | sudo tee -a  /sys/class/leds/helios4\:green\:status/delay_on
echo 200 | sudo tee -a  /sys/class/leds/helios4\:green\:status/delay_off

!!! note The changes is not retained across reboot. Use startup script or udev rules to make it permanent.

Configuring Fault LED

While other LEDs are preconfigured, the fault LED remains unconfigured (trigger:none).

1. As Kernel Panic Indicator

To configure the LED as Kernel panic indicator, set the trigger to panic. However this functionality might be redundant with Status LED, since if a kernel panic occurs and/or system hangs, the Status LED will no longer blink.

To trigger kernel panic to test the LED, run

echo c > /proc/sysrq-trigger

!!! warning Triggering kernel panic can lead to data loss. Use with caution!

2. As RAID Fault Indicator

To configure the LED as RAID fault indicator, please refer to MDADM: Configure Fault LED

!!! note On Armbian builds, this is the default setting for fault LED.