kobol-wiki/docs/helios64/install/first-start.md
Gauthier Provost 4de6afa6b8 Split install guide into 4 pages:
* Preliminary
* eMMC Install
* SDcard Install
* First Start
2020-10-14 14:02:37 +08:00

5.9 KiB

Step 1 - Connect to Helios64 serial console

Under Windows

!!! Important For Windows version prior to Windows 10, you will need to install the FTDI driver in order to access the USB to serial bridge used by Helios64. You can find the driver here.

  1. Download PuTTY and install it on your computer.

  2. Make sure your serial communication device is already detected by system. Serial detected

  3. Select connection type serial.
    Putty connect

  4. Setup serial port settings (Serial line : COM3 and Speed : 1500000), then press 'Open'
    Putty config

!!! note The serial port detection may vary on different system, please make sure to check the device manager to get the information of correct serial port to connect to Helios64. Check this link to learn how to determine the right COM port.

Under Linux (via Terminal)

1. Install picocom

Use apt-get under Debian/Ubuntu

$ sudo apt-get install picocom

Use yum under RHEL / CentOS / Fedora Linux

$ sudo yum install picocom

2. Connect to serial with picocom

$ sudo picocom -b 1500000 /dev/ttyUSB0

Picocom

To exit picocom do Ctrl-a then q button in squence

!!! note Using command ls -la /dev/ttyUSB* you should be able the find the USB to serial bridge device used by Helios64. Under Linux the device will be named /dev/ttyUSBx, where x is a digit.

Under Mac OS (via Terminal)

!!! Important For Mac OS you might need to install the FTDI driver in order to access the USB to serial bridge used by Helios64. You can find the driver here.

Connect serial using the screen command

$ screen /dev/tty.usbserial-XXXXXXXX 1500000 -L

To exit the session do Ctrl-a then Ctrl-k

!!! note Using command ls -la /dev/tty.usb* you should be able the find the USB to serial bridge device used by Helios64. Under Mac OS the device will be named /dev/tty.usbserial-xxxxxxxx, where xxxxxxxx is some serial number.

Step 2 - Power-Up Helios64

Now that everything is ready you can plug-in the AC adapter and push the Power Button.

Enclosure Power ON

If you are using Helios64 without an enclosure:

Enclosure Power ON

You should see Helios64 boot logs on the Serial Console.

Boot Output

Step 3 - Log in

!!! note You might need to press Enter for the login prompt to come up.

If system didn't auto logged-in. Default credential for Debian or Ubuntu image

helios64 login: root
Password: 1234

You will be prompted to change the root password and then create a new user account.

First Login

Step 4 - Check/Set IP address

Check IP address

By default Helios64 will try to obtain an IP address via DHCP. To figure out what is the allocated IP address you will need to type the following command in the console.

ip addr show dev eth0

Network Config

Here the IP address of Helios64 is 10.10.10.1.

Set IP address

If you wish to manually configure your IP address you can use the armbian-config tool.

armbian-config

Select the Network section:

Armbian-config

Navigate to IP to configure your IPv4 address:

Armbian-config

Select the Ethernet interface you want to assign a fixed IPv4 address. In this case we select eth0 which correspond to LAN port 1:

Armbian-config

Select Static:

Armbian-config

Provide the IP Address, Netmask, and Gateway information that you want to assign:

Armbian-config

Press ESC till you exit armbian-config tool.

You will have to reboot for the network settings to take effect.

sudo reboot

!!! info You can also refer to the following Debian Wiki Page for advanced network settings.

Step 5 - Connect to Helios64 via SSH

You can now connect by SSH to your Helios64 to carry on with your configuration.

Here is the example when we use linux client:

SSH Login

You can use putty as the SSH client if you are using windows:

Putty SSH

What to do next ?

You can use armbian-config which provides an easy way to install 3rd party applications like OpenMediaVault, NextCloud, Syncthing, Emby and many more.

Here an example on how to install software OpenMediaVault (OMV) using the armbian-config.

sudo armbian-config

Select Software section:

!armbian-config Main Menu

Navigate to Softy:

!armbian-config Software

Then choose OMV, to install the OpenMediaVault:

!armbian-config Selection

Wait the install process to complete:

!armbian-config Selection

Now you should be able to connect to OpenMediaVault (OMV) Control Panel.

Open your web browser and go to the one of the following addresses :

Default credential :

  • Username: admin
  • Password: openmediavault