kobol-wiki/docs/helios4/hardware.md
Gauthier Provost 312587c675 Restructure wiki to prepare for Helios64.
* Move all previous info into Helios4 subfolder
* Add helios64 subfolder
* Update all url link

Note: http server has been configure to ensure existing inbound link can 
still be resolved to the right page.
2019-12-13 16:15:54 +08:00

142 lines
5.1 KiB
Markdown

## Block Diagram
### Helios4 Carrier Board
![!Block Diagram](/helios4/img/hardware/helios4_block_diagram.jpg)
### A388 System-On-Chip
![!Block Diagram](/helios4/img/hardware/soc_block_diagram.png)
## Connector / Interface List
![!Board Legend](/helios4/img/hardware/board_legend.jpg)
Name |Peripheral Type|Connector Type|Details
-----|---------------|--------------|-------
CON2|Serial port|Micro-USB Connector|Via onboard FTDI USB-to-UART0 bridge
*J8*|*RC Battery*|*Not populated*|*External battery source for RTC clock*
J9|I2C|4x1 Pin Male Header|I2C Bus 1
J10|Fan|4x1 Pin Male Header|PWM and RPM support
J12|GPIO|7x2 Pin Male Header|GPIO configurable as input or output<br>Via IO Expander on I2C Bus 0
*J13*|*Serial port*|*Not populated*|*SoM UART0 interface*
J14|HDD Power|Molex 4-Pin Female|Rated for 2x HDD
J15|LAN|RJ45|Gigabit Ethernet
J16|DC connector|Kycon 4-Pin Mini-DIN|DC input 12V / 8A
J17|Fan|4x1 Pin Male Header|PWM and RPM support
J18|LED Panel|5x2 Pin Male Header|Expansion port of on-board LED
J19|HDD Power|Molex 4-Pin Female|Rated for 2x HDD
SW1|Boot Mode|Dip Switch|Boot mode selector :<br> SPI,MMC,UART,SATA
SW2|LED Mode|Dip Switch|LED mode selection :<br> board or expansion panel
U3|microSD|Push-Push card connector|Support SDHC and SDXC
U4|USB 3.0|Dual Port USB3.0|Type A
U16|Reset|Push Button|CPU Reset
U10|SATA|SATA 3.0|Port 0 (SATA1)
U11|SATA|SATA 3.0|Port 1 (SATA2)
U12|SATA|SATA 3.0|Port 2 (SATA3)
U13|SATA|SATA 3.0|Port 3 (SATA4)
## Boot Modes
Helios4 supports 4 boot modes that can be chosen by using the dipswitch SW1.
![Dipswitch modes](/helios4/img/hardware/dipswitch_modes.jpg)
All the ready-to-use images we provide are for the **SD Card** boot mode.
Please refer to [U-boot](/helios4/uboot) section to know how to use the other modes.
## LED indicators
LED Name|Color|Description
---|---|---
LED1|green|System heartbeat
LED2|red|Error status
LED3|green|SATA1 activity
LED4|green|SATA2 activity
LED5|green|SATA3 activity
LED6|green|SATA4 activity
LED7|green|USB activity
LED8|green|Power indicator
Helios4 board was designed to either use the on-board LEDs or use an expansion panel (not-available). To use the on-board LEDs insure to switch to ON the dipswitch SW2.
![Dipswitch LED](/helios4/img/hardware/dipswitch_led_on.jpg)
## Reset Button
Helios4 board provides a RESET push button (U16) to hard reset the SoC (System-On-Chip).
![Reset Button](/helios4/img/hardware/reset_button.jpg)
!!! Important
This button only resets the SoC and not the overall board. For instance it won't reset the HDD.
## I2C Interface
Helios4 board exposes on header J9 the SoC I2C Bus 1. Below is the header pin-out, the little arrow on the PCB indicates the ground pin.
![I2C Pinout](/helios4/img/hardware/i2c_pinout.png)
## Power Consumption
**Board only**
* Idle : 3.6 Watts
* Active : 5.6 Watts
**Full Kit (with 4x HDDs)**
| State | AC calculated<br>power consumption | DC measured<br>power consumption | Remarks |
|---------------------|----------------------|----------------------|---------------------|
| Idle | 19.3 W | 16.8 W | |
| HDD Read Access | 27.4 W | 22.8 W | |
| HDD Write Access | 30.3 W | 25.2 W | |
| Standby | 8.0 W | 6.7 W | HDD in Standby mode |
| Suspend-to-Ram | 7.2 W | 6.0 W | HDD in Standby mode |
!!! note
Measures were done using a Current Clamp Meter on the Helios4 12V DC input. AC Power consumption is calculated based on a AC/DC conversion efficiency of 85%.
* Meter tool : Extech 380942 - 30A True RMS AC/DC Mini Clamp
* AC/DC Adapter : yczx1268 (efficiency : 85%)
* AC Input Voltage: 220V
* HDD: 4x WD Red 2TB (WD20EFRX) configured as RAID10
* Network : Connected at 1000Mb/s
* OS: ARMBIAN 5.73 stable Debian GNU/Linux 9 (stretch) 4.14.98-mvebu
## HDD Recommendation List
We recommend HDD which are designed for NAS (Network Attached Storage). Those NAS HDD are specially conceived for reliable 24/7 operation and offers lower power consumption and dissipation, less vibration and noise, and finally better warranty. We recommend the following models :
**Western Digital** : WD Red NAS (1, 2, 3, 4, 6, 8 and 10TB)
- WD10EFRX
- WD20EFRX
- WD30EFRX
- WD40EFRX
- WD60EFRX
- WD80EFZX
- WD100EFAX
**Seagate** : IronWolf NAS (1, 2, 3, 4, 6, 8 and 10TB)
- ST1000VN002
- ST2000VN004
- ST3000VN007
- ST4000VN008
- ST6000VN0041
- ST8000VN0022
- ST10000VN0004
**HGST** : Deskstar NAS (4, 6 and 8TB)
- 0S04005
- 0S04007
- 0S04012
!!! note
We recommend to order from different shop to avoid having all the drives from the same factory batch. For instance, you should order 2x HDDs from one shop, then the 2 others from another shop.
## HDD / SSD Compability List
Please refer to [Synology DS416j Compatibility List](https://www.synology.com/en-global/compatibility?search_by=products&model=DS416j&category=hdds&p=1) that covers a large number of tested drives. The DS416j used the same SoC family than Helios4.