3.8 KiB
These instructions document how FreeBSD (head) can be built for, and installed on the Helios-4. This has been made possible by the initial port of FreeBSD to the SolidRun Clearfog that has been submitted June 2017 by Semihalf and Stormshield: Read the announcement here.
Compiling FreeBSD
There is a manual way to compile FreeBSD, and it is documented on the SolidRun Wiki Clearfog page. The process is almost identical for the Helios-4 in that a suitable DTB has to be copied to the boot partition. The following instructions use the crochet utility for automating the build and imaging process.
Get the source
We use a fork of crochet that has added the necessary bits for Helios-4.
mkdir work; cd work
git clone --checkout pr-clearfog https://github.com/Artox/crochet.git
svn checkout https://svn.freebsd.org/base/head src
Configure the build
crochet uses a configuration file to perform builds. config.sh.sample is an example, and can be adapted as needed. As a bare minimum, a line
board_setup Clearfog
has to be at the top near the other commented board_setup_* lines. In addition enabling the growfs feature has proven useful for autoresizing the rootfs on first boot: simply uncomment the line
option Growfs
There are plenty of other settings to change, but these suffice for creating a bootable image.
Build
Navigate to the crochet folder, and assuming you called your config file config.sh, run:
sudo /bin/sh crochet.sh -c config.sh
On success an sdcard image will have been produced in the build directory, for example /opt/work/build/FreeBSD-armv7-12.0-GENERIC-333641-Clearfog.img. This image is a complete FreeBSD installation, without U-Boot installed.
Create SD-Card
The previously created image can be written to an sdcard as is; assuming your SD-Card is available at /dev/sdX, write the image to it:
pv FreeBSD-armv7-12.0-GENERIC-333641-Clearfog.img | sudo tee /dev/sdX >/dev/null
Boot It
In an ideal world U-Boot would already be installed in SPI flash, including the necessary patch for FreeBSD. If you happen to have such an ideal system, you may skip the next section
Install U-Boot
Please refer to U-boot for build instructions.
The Boot-ROM expects to find U-Boot at 512 bytes into the sdcard. Assuming your SD-Card is available at /dev/sdX, write the u-boot binary to it using dd:
sudo dd bs=512 seek=1 conv=fsync if=u-boot-a38x-5-15-mmc.bin of=/dev/sdX
Boot
Insert the sd-card into your device, connect a serial console and turn it on. The U-Boot console will come up with a prompt:
Hit any key to stop autoboot: 3
Press a key to abort automatic boot, or wait till it fails to do a network boot. Once it has dropped to a terminal prompt, indicated by Marvell>> at the start of the line, configure U-Boot to load the FreeBSD loader by default:
setenv fdt_addr_r 0x1000000
setenv loadaddr 0x2000000
setenv bootcmd 'fatload mmc 0:2 ${fdt_addr_r} armada-388-helios4.dtb; fatload mmc 0:2 ${loadaddr} ubldr.bin; go ${loadaddr}'
setenv bootdelay 1
saveenv
Beware: You probably have to paste these lines individually, or U-Boot may mess it up. You can set bootdelay to 0 if you want, that way you will never again get to the u-boot console unless you delete the FreeBSD loader.
Finally, type boot, or reset, or reset the board by pressing the button labeled U16 on the board. This time, just sit back and watch as FreeBSD comes up.
Default User
The FreeBSD image by crochet comes with an unlocked root account. This means you do not need to enter a password to log in as root.