168 lines
5.4 KiB
Markdown
168 lines
5.4 KiB
Markdown
The A388 System-On-Module used by Helios4 provides an SPI NOR flash [Winbond W25Q32BV](https://media.digikey.com/pdf/Data%20Sheets/Winbond%20PDFs/W25Q32BV.pdf) connected to SPI bus 1 Chip Select 0.
|
|
|
|
By default, Helios4 is configured to boot from microSD card. To boot from SPI NOR flash (after [writing U-Boot into SPI NOR flash](#write-u-boot-to-spi-nor-flash)), please change Boot Mode on DIP Switch **SW1** to:
|
|
|
|
|
|
|
|
|
|
## Build U-Boot for SPI NOR flash
|
|
|
|
Refer to [U-Boot](/uboot) page to build the image.
|
|
|
|
*A prebuilt SPI image of U-Boot 2013.01 for Armbian OS can be downloaded from [here](/files/uboot/u-boot-armbian-2013.01-spi.bin).*
|
|
|
|
## Write U-Boot to SPI NOR flash
|
|
|
|
!!! important
|
|
Concurrent access on SPI NOR and SATA drives can lead to unstable SATA. The following instructions has taken this issue into consideration and workaround it by disabling the SATA temporary.
|
|
|
|
### Under Armbian
|
|
|
|
1) Edit /boot/armbianEnv.txt and enable spi_workaround
|
|
|
|
`spi_workaround=on`
|
|
|
|
2) Reboot the system to apply the change
|
|
|
|
3) Log in to Helios4, verify whether mtdblock0 is present using **lsblk**
|
|
|
|
```
|
|
lsblk
|
|
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
|
|
mtdblock0 31:0 0 4M 0 disk
|
|
mmcblk0 179:0 0 14.9G 0 disk
|
|
└─mmcblk0p1 179:1 0 14.8G 0 part /
|
|
```
|
|
|
|
4) Run **nand-sata-install** utility
|
|
|
|
```
|
|
sudo nand-sata-install
|
|
```
|
|
|
|
5) Select option **5 Install the bootloader to SPI Flash**
|
|
|
|
6) If you want to take the opportunity to move your RootFS to another device, jump to this [section](#moving-rootfs-to-other-device). Otherwise you may disable spi_workaround in /boot/armbianEnv.txt
|
|
|
|
`spi_workaround=off`
|
|
|
|
7) Set DIP switches **SW1** to SPI Boot and reboot the system.
|
|
|
|
|
|
|
|
### Under Generic Linux
|
|
|
|
!!! info
|
|
You will need to access to Helios4 via Serial Console. Please refer to [Install](/install/#step-4-connect-to-helios4-serial-console) page for instructions.
|
|
|
|
1) Upload the U-Boot SPI binary that you built to Helios4 and rename it as **u-boot-spi.bin**.
|
|
|
|
2) Download boot_spi_en.scr from [here](/files/uboot/boot_spi_en.scr) and put it to /boot/.
|
|
|
|
```
|
|
sudo wget https://wiki.kobol.io/files/uboot/boot_spi_en.scr -O /boot/boot_spi_en.scr
|
|
```
|
|
|
|
*Source code of boot_spi_en.scr can be found [here](/files/uboot/boot_spi_en.cmd).*
|
|
|
|
3) Switch to Helios4 serial console, then reboot the system
|
|
|
|
```
|
|
sudo Reboot
|
|
```
|
|
|
|
4) Press any key to cancel the U-Boot autoboot and execute these commands
|
|
|
|
```
|
|
setenv script_name "/boot/boot_spi_en.scr"
|
|
stage_boot mmc_scr
|
|
```
|
|
|
|
It will boot to Linux with modified device tree.
|
|
|
|
5) Log in to Helios4, verify whether mtdblock0 is present using **lsblk**
|
|
|
|
```
|
|
lsblk
|
|
NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT
|
|
mtdblock0 31:0 0 4M 0 disk
|
|
mmcblk0 179:0 0 14.9G 0 disk
|
|
└─mmcblk0p1 179:1 0 14.8G 0 part /
|
|
```
|
|
|
|
6) Write the U-Boot binary to SPI flash using this command
|
|
|
|
```
|
|
sudo dd if=~/u-boot-spi.bin of=/dev/mtdblock0
|
|
```
|
|
|
|
7) Set DIP switches **SW1** to SPI Boot and reboot the system.
|
|
|
|
|
|
|
|
Observe the first lines of boot message on serial console, it should display
|
|
|
|
```
|
|
BootROM - 1.73
|
|
Booting from SPI flash
|
|
```
|
|
|
|
## Set Up U-Boot Environment
|
|
|
|
!!! important
|
|
Prebuilt SPI images for Armbian are configured to automatically run /boot/boot.scr on microSD or USB drive. There is no need to set up u-boot environment to boot Armbian.
|
|
|
|
Add U-Boot ENV variables to prevent U-Boot to relocate fdt and initrd into RAM address that is not accessible by kernel, and set the correct device tree name for Helios4 board
|
|
|
|
```
|
|
setenv fdt_high 0xffffffff
|
|
setenv initrd_high 0xffffffff
|
|
setenv fdtfile armada-388-helios4.dtb
|
|
saveenv
|
|
```
|
|
|
|
- To automatically boot Linux on microSD card
|
|
|
|
```
|
|
setenv bootargs '${console} root=/dev/mmcblk0p1 rootwait'
|
|
setenv bootcmd 'ext2load mmc 0:1 ${kernel_addr_r} /boot/zImage; ext2load mmc 0:1 ${ramdisk_addr_r} /boot/uInitrd; ext2load mmc 0:1 ${fdt_addr} /boot/dtb/${fdtfile}; bootz ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr}'
|
|
saveenv
|
|
```
|
|
|
|
- To automatically boot Linux on USB drive (assume UUID=1234)
|
|
|
|
```
|
|
setenv bootargs '${console} root=UUID=1234 rootwait'
|
|
setenv bootcmd 'usb start; ext2load usb 0:1 ${kernel_addr_r} /boot/zImage; ext2load usb 0:1 ${ramdisk_addr_r} /boot/uInitrd; ext2load usb 0:1 ${fdt_addr} /boot/dtb/${fdtfile}; bootz ${kernel_addr_r} ${ramdisk_addr_r} ${fdt_addr}'
|
|
saveenv
|
|
```
|
|
|
|
## Moving RootFS to Other Device
|
|
|
|
Now you have the option to move your Root FileSystem to a storage device connected to USB3.0. Under Armbian you can use the **nand-sata-install** utility to easily take care of this procedure.
|
|
|
|
!!! Important
|
|
Only the USB **top port** is supported by U-Boot. So you need to plug the storage device on which you want to move the RootFS in the top port.
|
|
|
|
1) Enable the *spi_workaround* if it's not enabled yet (refer to the above [section](#under-armbian)).
|
|
|
|
2) Run **nand-sata-install** utility
|
|
```
|
|
sudo nand-sata-install
|
|
```
|
|
|
|
3) Select option **6 Boot from SPI - system on SATA, USB or NVMe**
|
|
|
|
4) When RootFS migration is done, disable spi_workaround.
|
|
|
|
5) Set DIP switches **SW1** to SPI Boot and reboot the system.
|
|
|
|
6) Check that your system has mounted the RootFS from the correct device.
|
|
*It shouldn't be /dev/mmcblk0p1*
|
|
|
|
```
|
|
grep '/ ' /proc/mounts
|
|
/dev/sdb1 / ext4 rw,noatime,nodiratime,errors=remount-ro,commit=600 0 0
|
|
```
|
|
|
|
You can now remove your microSD Card. However you should keep it aside, it can be useful in case you need to recover your system.
|